Nowadays, Samsung washers are popular among customers due to their reliability. However, problems can arise when your appliance refuses to spin, leaving you with wet clothes that can’t be dried. If your Samsung washing machine is not spinning properly, there could be a few potential causes behind it.
The filter can become clogged with lint, dirt, and other debris that builds up over time. This can cause the motor to become overloaded and unable to spin the drum properly. Additionally, lint and other debris can accumulate in the drain hose and prevent water from draining away quickly enough for the washer to spin efficiently. Cleaning out your filter regularly can help ensure your washer runs at its best.
The process for cleaning the filter can differ depending on your model, so it’s important to consult your manual or contact a service technician to ensure you’re doing it correctly. When cleaning, use water and soap if needed to remove any build-up inside the filter. Be sure to dry all components before reassembling them back into the washing machine.
Another explanation for why your Samsung washer does not spin is a faulty lid switch. This component detects when the lid is open or closed during the cycle. If it fails, the machine won’t be able to sense that the lid is securely closed, and it won’t start spinning.
To determine if this is causing your issue, you can take off the top panel of your device and locate the wiring at its bottom left side. If it’s loose or disconnected from its connector, then there’s a good chance that this component has gone bad and needs to be replaced. It’s best to seek professional help if you’re unsure about how to inspect these components yourself.
Overloading your washer can cause it to not spin, as the internal parts of the machine may be unable to handle the excessive weight. When too much laundry is loaded into a washer, the agitator or drum cannot move properly and will cause strain on all its components. This extra pressure can lead to unbalanced loads that either don’t spin at all or shake violently.
If the Samsung washing machine won’t spin, the issue could be caused by a broken belt. A belt connects two parts, such as the motor and the drum, allowing them to work together. When a belt breaks, it stops the drum from spinning and washing clothes properly. Unfortunately, this can be difficult to diagnose without opening up your machine since there aren’t any visible signs that a belt has broken.
To check for a broken belt in your Samsung washer, first, unplug it and remove its back panel or access door. Locate the drive belt on the bottom of your machine and inspect it for any tears or frays that could indicate that it is worn out or snapped. If you find any damage to the drive belt, replace it with an exact replacement part to restore the full operation of your washing machine.
A broken motor is one of the worst-case scenarios when it comes to a Samsung washer not spinning. The most obvious sign of it is if the drum doesn’t spin at all; however, you may also find that it only spins at slower speeds than usual. If this is the case, it is likely that the motor has gone bad and needs to be replaced.
Replacing a motor in a washer can be an expensive and time-consuming process, but it may be necessary in order to get your washing machine running again. It is best to contact an experienced repair technician who specializes in Samsung products in order to ensure that the job is done properly and safely.
In order to fix your Samsung washer that won’t spin, check the size and weight of the load. A small load is 1/3 full, while a large load should be 3/4 full. If you overload your machine with too much laundry, it won’t be able to spin properly due to excess friction.
Then you need to spread out the clothes, so they’re evenly distributed around the drum. If there are too many clothes in one section of the tub, they can become unbalanced and cause problems when spinning.
Additionally, make sure all items are properly secured inside the drum. Items such as laces or strings need to be tied together before being placed into the machine; otherwise, they can get tangled during a washing cycle and lead to an uneven spin.
Finally, you should select the correct cycle. Different washers have different cycles, each designed for specific fabrics and soils. For example, select a normal cycle with warm water temperature for everyday loads such as towels and sheets. Use a gentle cycle with cool water temperature for more delicate items like lingerie or woollens. If a wrong cycle is chosen, it can affect how well the washer performs and cause errors.
Doing these things before every cycle can help ensure that your washer spins properly and prevents any further issues from occurring.
REFERENCES
https://www.samsung.com/us/support/troubleshooting/TSG01000997/
Looking for Samsung washing machine repair services? Our company has many years of experience in servicing large laundry appliances. We can repair any washing machine, regardless of brand, modification, year of manufacture.
Book online
Other Articles
Learn how to fix your Samsung washer if it’s not draining properly with these helpful steps.
Fix a bottom leak in your Samsung washer with these easy-to-follow steps to prevent further damage.
If your Samsung oven isn’t heating, follow these troubleshooting steps to get it back to work.
